B-Grade 12V DC Long 61kg (134lbs), Force Linear Actuator, Electric Piston Motor
We are one of the most popular suppliers of linear actuators in the United Kingdom, with full product support and user advice available. We are highly knowledgeable in our field, insured, and VAT-registered.
(and sometimes B-grade items available at a discount). Also find A-grade (standard) actuators of this and other models on our website. Prices displayed are inclusive of 20% UK VAT, if you require a VAT invoice please request this when ordering. The'B-grade' actuators on this listing have some surface scratches from storage and transport but are otherwise as-new and fully functional. The GLA600-S model actuator on this listing is a relatively fast-extending actuator available with large travel distances of either 400mm (15.75") or 700mm (27.5"). Typical applications include driving electric gates, automatic windows and other home automation assemblies. Each actuator may provide a pushing or pulling force of up to 600N (61kg, 134lbs) and a travel speed of up to 28mm/s when under no-load.
The large travel provided by the GLA600-S makes it useful for actuating assemblies which require greater leverage about a pivot point, in this way it can reduce the forces that occur at the actuator fixing points when compared to a shorter-stroke higher-force actuator doing the same job. In order to obtain a high travel speed the lead-screw of the actuator has a large pitch (and four starts), which mean that it may back-drive under heavy loads. The operating voltage of 12V DC makes it suitable for powering from a lead-acid battery such as a car battery, or running from a mains to 12V DC adapter which are widely available.
The actuator comes with a 0.8m PVC insulated lead as standard (black external sleeve with two internal cores, one red and one black) with uncovered lead ends. To change the direction of travel simply swap the polarity of the DC power source to the two actuator leads (this may be achieved using hardware such as our rocker switch harness or GLA-CU-X2 remote control unit). By varying the input voltage between 0-12V DC it is possible to control the speed of the actuator. Reducing the voltage will also reduce load capacity (for example at 6V the actuator will have roughly half of the maximum load capacity at 12V). This actuator is designed primarily for compression loads, it will typically work OK in tension, up to the same rated maximum load, but can be more susceptible to damage from overloading. Shock loads through the mounting points should be avoided. Experienced users who wish to extract greater power from the actuator (at their own risk) should abide by a practical operation ceiling of 18V, above which the motor, diodes and limit switches of the actuator would be significantly more likely to fail.
Be aware that the current draw will be greater if the actuator is run at above 12V DC and the duty cycle should be reduced to help avoid over-heating. Ensure that the control hardware and power source are capable of providing sufficient current for the loads you expect the actuator to experience.
We cannot be held liable for damage caused to connected hardware due to inappropriate hardware selection. CAD models (in STEP, IGS, Autodesk Fusion formats) of the actuator are available upon request. Nominal 12V DC, up to 50W. 6.5A (the actuator should only ever be allowed to stall for short <0.5s periods). < 50dB under no-load < 55dB under full-load.
40% this is the maximum proportion of time that the actuator may be in operation for, up to 2minutes during any continuous stretch. The duty cycle should be reduced below 20% for average loads >300N. Please be aware that there may some variation in the operating performance from actuator to actuator, as a rule-of-thumb allow for a 5% difference above/below the given values. If intending to use two actuators together to drive the same assembly connect them in parallel to the input current and ensure that the driven assembly is rigid enough to transfer forces between the actuators (so as to prevent twisting if one actuator is slightly faster than the other). 105mm + Stroke length (distance from front to rear mounting hole centres).
One is towards the end of the piston rod, the other is on the rear of the gearbox housing. Aluminium & Zinc plated Steel, rated to IP54.
Installed internally at ends of travel (fixed-position). The circuit functions like this.
0.8m, excluding optional DC connector cable which brings the total length to 1.1m. The item "B-Grade 12V DC Long 61kg (134lbs), Force Linear Actuator, Electric Piston Motor" is in sale since Friday, September 29, 2017. This item is in the category "Business, Office & Industrial\Automation, Motors & Drives\Linear Motion\Linear Actuators". The seller is "gimsonrobotics" and is located in Bristol, Avon. This item can be shipped worldwide.
- Brand: Gimson Robotics
- MPN: GLA600-S